Skip to content
Available 24/7 Emergency Gate Repair Service
Shield Gate Repair

Celina · Collin County

Swing Gate Repair in Celina, TX

Swing gate repair in Celina for long ranch and acreage swing gates and the swing gates on homes in the new developments. We start with hinges and posts, because a swing leaf is only as good as what holds it.

  • Licensed & Insured
  • 16+ Years Experience
  • Open 24/7
  • Residential & Commercial
Call (214) 735-4314Get a Free Estimate

Swing Gate Repair in Celina: what we see

Ranch and acreage swing gates are typical of Celina’s extraterritorial land, and they are long. A wide farm leaf is a lever, and the clay under its hinge post shrinks in summer and swells after rain, so the post leans, the leaf drops at the latch end and the operator has to lift as well as push. Many of these gates run on solar and battery, so the extra current also drains the battery faster. In the developments, swing gate faults are more often limits and settings on new installations.

We release the operator, swing the leaf by hand and check the hinges, the post, the latch end and any support wheel. Then the actuator, mounting brackets, limits and force settings. Most swing gate repair in Celina is mechanical first: hinges, leveling and post work, then actuator or battery. On properties along FM 455, FM 428 or Preston Road outside the developments, we also check how the gate stops and latches, since wind loads a long leaf hard.

Real jobs nearby

Our nearest documented jobs to Celina

Work our technicians have documented, each shown under the city it was in.

All case studies

On video

Gate jobs near Celina on video

Filmed on our own jobs, each marked with its city: Prosper (6 mi), Richardson (26 mi), University Park (32 mi).

Signs you need swing gate repair

  • Gate sags, or the latch no longer lines upWorn hinges, a post that has moved, or a gate frame that has racked out of square
  • Gate drags on the drivewayA leaning post or hinge wear — the operator is now fighting the ground on every cycle
  • Arm moves but the gate barely doesA bent or worn operator arm, a loose or broken bracket, or a stripped drive
  • One leaf of a double gate lags or will not closeAn arm or board fault on that side, or the two leaves have drifted out of sync
  • Gate will not hold closed, or swings in the windA missing gate stop or latch, or an operator left in manual release
  • Hums at the start of travel and stallsA failing capacitor, or a gate that has become too heavy to start moving

Swing Gate Repair across Dallas–Fort Worth →

Our recent swing gate repair work

Photos from our technicians' recent jobs across Dallas–Fort Worth.

  • Ornate wrought iron double swing gates between stone-clad pillars, both leaves open with an operator at each post
  • A black iron swing gate with scroll detailing and an operator arm, opening onto a driveway beside a brick house
  • A white ornamental iron swing gate with spear finials and a linear operator arm
  • A black iron swing gate with a diagonal-bar pattern, its operator arm and open control box on a brick pillar
  • Double ornamental iron swing gates between stone pillars, with the operator box at the base
  • A black iron swing gate with patriotic bunting on the fence and its arm operator at the hinge

Customer testimonials

What our customers say

Customers across Dallas–Fort Worth, filmed at their own gates. We bring the same team to Celina.

Watch every customer video

Areas we cover in Celina

  • Light Farms
  • Mustang Lakes
  • Cambridge Crossing
  • Creeks of Legacy
  • Sutton Fields
  • Lilyana

Swing Gate Repair in Celina: questions

Why does our long ranch gate in Celina keep stopping before it closes?

A dropped leaf is the usual reason. As the hinge post leans in the clay, the far end drags or meets the latch late, and the operator stops on overload. On solar gates the extra effort also pulls the battery down. We level the leaf, adjust or replace hinges, check the post, and then test the battery and operator under load.

Can a swing gate actuator be repaired or must it be replaced?

It depends on the fault. A bent extension tube, a worn mounting bracket or a limit that has drifted can often be fixed. A motor or gear failure inside a sealed actuator usually means replacing the actuator, not the whole operator. We confirm which part has failed and whether a compatible actuator is available for your control board before ordering.

More gate services in Celina

Gate opener brands we repair in Celina

Gate Not Working Right Now?

We answer the phone 24/7. If you are stuck, call and we will talk you through the manual release before anyone arrives. See what counts as a gate emergency.

(214) 735-4314Request a callback
Call NowText UsEstimate