Southlake · Tarrant County
Sliding Gate Repair in Southlake, TX
Sliding gate repair in Southlake for wide estate driveway slides and subdivision entrance gates. Chain and roller wear is the usual fault here, and fixing it often brings a struggling operator back to normal.
- Licensed & Insured
- 16+ Years Experience
- Open 24/7
- Residential & Commercial
Sliding Gate Repair in Southlake: what we see
A Southlake estate slide gate is often long and heavy, ornamental iron spanning a wide drive, and it rides on rollers in a track or on a cantilever frame. After twenty-plus years the rollers wear flat, bearings get noisy, the track collects debris, and clay that shifts under the slab can tilt it slightly out of level. The operator feels every one of those as extra load. That is why so many sliding gate calls here start with a gate that jerks, hesitates at one point, or reverses near the end of travel.
Our order is rollers and track, guide wheels and gate stops, then chain tension, sprockets and idlers, and only then the operator, its limits and the board. Most Southlake sliding gate repair work ends with new rollers, a chain or a limit adjustment. If the track itself has been damaged by a vehicle, we repair or replace that section. Around Carillon, Clariden Ranch and N Carroll Ave, we also check the photo-eyes and edge sensors across the opening, since a slide gate needs working entrapment protection.
Real jobs nearby
Our nearest documented jobs to Southlake
Work our technicians have documented, each shown under the city it was in.
US AutomaticFort Worth, TXresidentialAnother Company Said Replace It. We Refurbished It Instead.
A Fort Worth homeowner had been told the solar operator needed replacing. The board was corroded, the arm needed repair and the gate was leaning — all fixable.
Read the case study
LiftMasterUniversity Park, TXresidentialA Gate Left Unused for a Year, a Broken Bracket and a Broken Arm
The customer had not operated the gate in about twelve months and wanted it working again. The bracket and the operator arm had both failed.
Read the case study
LiftMasterRichardson, TXresidentialThe Board Had Physically Fallen Inside the Operator
A Sunday call from a senior customer. The circuit board had come loose and failed, and because it had stopped charging them, both backup batteries had gone too.
Read the case study
On video
Gate jobs near Southlake on video
Filmed on our own jobs, each marked with its city: Fort Worth (17 mi), University Park (21 mi), Richardson (23 mi).
Signs you need sliding gate repair
- Gate has come off its track or leans out of lineDebris in the track, a worn V-groove wheel, or a bent or damaged track
- Grinding, scraping or a heavy rumble as it movesWheel bearings failing, a flat-spotted wheel, or the gate rubbing a guide roller
- Starts, stops partway and reversesThe gate is binding on the track or a roller, and the operator reads the extra load as an obstruction
- Chain slack, jumping the sprocket or snappedA stretched or rusted chain, a worn idler, or chain brackets out of line
- Motor runs but the gate does not moveChain off the sprocket, a broken drive sprocket, or a slipping clutch
- Gate rolls on its own or will not stay shutTrack slope, a missing or broken gate stop, or a worn latch
Our recent sliding gate repair work
Photos from our technicians' recent jobs across Dallas–Fort Worth.
Customer testimonials
What our customers say
Customers across Dallas–Fort Worth, filmed at their own gates. We bring the same team to Southlake.
Areas we cover in Southlake
- Timarron
- Carillon
- Kirkwood Hollow
- Shady Oaks
- Coventry Manor
- Clariden Ranch
Sliding Gate Repair in Southlake: questions
Why does our slide gate in Southlake drag at one spot?
A single tight spot usually means the track has lifted or dropped there, often where the slab or ground has moved in the clay, or a roller has a flat. We run the gate by hand to find it, then level or repair the track and replace worn rollers. Ignoring it overworks the operator and stretches the chain quickly.
How tight should the chain on a sliding gate be?
Snug, with a little sag along its length, never guitar-string tight. Too loose and it jumps the sprocket; too tight and it loads the motor bearings and wears the sprocket teeth. We set it to the operator maker’s guidance, check the brackets at both ends of the gate, and replace the chain if it has stretched past adjustment.
More gate services in Southlake
- Gate repair in Southlake
- Automatic Gate Repair in Southlake
- Electric Gate Repair in Southlake
- Driveway Gate Repair in Southlake
- Swing Gate Repair in Southlake
- Gate Opener Repair in Southlake
- Gate Motor Repair in Southlake
- Emergency Gate Repair in Southlake
- Commercial Gate Repair in Southlake
- Residential Gate Repair in Southlake
- Automatic Gate Installation in Southlake
- Electric Gate Installation in Southlake
- Sliding Gate Installation in Southlake
- Swing Gate Installation in Southlake
- Gate Opener Installation in Southlake
Gate opener brands we repair in Southlake
Gate Not Working Right Now?
We answer the phone 24/7. If you are stuck, call and we will talk you through the manual release before anyone arrives. See what counts as a gate emergency.